What Are You Doing Right Now
-
Good morning so far. Personal record of 415.
-
https://www.kickstarter.com/projects/fabcreator/fabcreator-lasers
https://vimeo.com/16769248940 & 100 Watt CO2 laser cutter, 100W goes for just 7k EUR right now. Looks great.
-
I'm getting ready to go on my first real vacation in what feels like eons... (It's really been only a year or three). Going to go hang out with the wife's family for two weeks!
So... I'll likely be mostly not on here while I'm gone, but you know how that goes. Heading from Georgia to Iowa by car... ~18hrs on a good run.
-
@dafyre said in What Are You Doing Right Now:
I'm getting ready to go on my first real vacation in what feels like eons... (It's really been only a year or three). Going to go hang out with the wife's family for two weeks!
So... I'll likely be mostly not on here while I'm gone, but you know how that goes. Heading from Georgia to Iowa by car... ~18hrs on a good run.
where in Iowa?
-
@Dashrender said in What Are You Doing Right Now:
@dafyre said in What Are You Doing Right Now:
I'm getting ready to go on my first real vacation in what feels like eons... (It's really been only a year or three). Going to go hang out with the wife's family for two weeks!
So... I'll likely be mostly not on here while I'm gone, but you know how that goes. Heading from Georgia to Iowa by car... ~18hrs on a good run.
where in Iowa?
We'll be around West Burlington.
-
@dafyre said in What Are You Doing Right Now:
@Dashrender said in What Are You Doing Right Now:
@dafyre said in What Are You Doing Right Now:
I'm getting ready to go on my first real vacation in what feels like eons... (It's really been only a year or three). Going to go hang out with the wife's family for two weeks!
So... I'll likely be mostly not on here while I'm gone, but you know how that goes. Heading from Georgia to Iowa by car... ~18hrs on a good run.
where in Iowa?
We'll be around West Burlington.
lol that's barely iowa
-
@Dashrender said in What Are You Doing Right Now:
@dafyre said in What Are You Doing Right Now:
@Dashrender said in What Are You Doing Right Now:
@dafyre said in What Are You Doing Right Now:
I'm getting ready to go on my first real vacation in what feels like eons... (It's really been only a year or three). Going to go hang out with the wife's family for two weeks!
So... I'll likely be mostly not on here while I'm gone, but you know how that goes. Heading from Georgia to Iowa by car... ~18hrs on a good run.
where in Iowa?
We'll be around West Burlington.
lol that's barely iowa
Anywhere in iowa is barely iowa
-
@wirestyle22 said in What Are You Doing Right Now:
@Dashrender said in What Are You Doing Right Now:
@dafyre said in What Are You Doing Right Now:
@Dashrender said in What Are You Doing Right Now:
@dafyre said in What Are You Doing Right Now:
I'm getting ready to go on my first real vacation in what feels like eons... (It's really been only a year or three). Going to go hang out with the wife's family for two weeks!
So... I'll likely be mostly not on here while I'm gone, but you know how that goes. Heading from Georgia to Iowa by car... ~18hrs on a good run.
where in Iowa?
We'll be around West Burlington.
lol that's barely iowa
Anywhere in iowa is barely iowa
Part of the state is the bits no other state in the area wanted to deal with
-
@thwr said in What Are You Doing Right Now:
@travisdh1 Normally yes, because of the timing. But you can use stepper motors which works pretty well with RPis.
This is a good one for roughly 2-3 dollar incl. a ULN2003 controller board:
If you're just using the steppers to turn the knobs and things on the controllers I suppose. I was assuming you'd want to directly control most of it using the electronic controllers. Adding local controls is easy, the only difficult part is making sure you're using the correct signaling going to the models.
-
Having problem is unitrends free and Linux agents.
Can't seem to find any good guides to diagnose why it's not running or listening/ -
@travisdh1 said in What Are You Doing Right Now:
@thwr said in What Are You Doing Right Now:
@travisdh1 Normally yes, because of the timing. But you can use stepper motors which works pretty well with RPis.
This is a good one for roughly 2-3 dollar incl. a ULN2003 controller board:
If you're just using the steppers to turn the knobs and things on the controllers I suppose. I was assuming you'd want to directly control most of it using the electronic controllers. Adding local controls is easy, the only difficult part is making sure you're using the correct signaling going to the models.
Sorry, that post was meant to be a reply to @MattSpeller and his robot arm project . Fat-finger-on-small-touchscreen-syndrome.
-
Waiting for the hot water system to warm up
-
Drove all night to get to Bucharest. We are camped out in the hotel by the airport now. We leave first thing in the morning.
-
I'm setting up XenServer on the first of the two host.
Sadly XS doesn't see the 16GB SD card, but it does see a 16GB USB.
-
@DustinB3403 said in What Are You Doing Right Now:
I'm setting up XenServer on the first of the two host.
Sadly XS doesn't see the 16GB SD card, but it does see a 16GB USB.
Is there a BIOS setting to make them look like SATA devices or similar?
-
@hobbit666 Nothing that I saw, but I could have overlooked it.
-
I'll confirm on the 2nd system in a few minutes.
-
A benefit for us to installing to USB is that I have plenty of 16GB USB's to clone too..
-
Bought an Amazon Tap today to compliment our Echo.
-
@DustinB3403 said in What Are You Doing Right Now:
A benefit for us to installing to USB is that I have plenty of 16GB USB's to clone too..
I had issues running XenServer from USB. not sure if it was just the USB or the Dell Server but had to install on local disks to get it booting and responsive.
